最大限度地延长电池寿命减少更换MaximizeBat
Abstract: The MAX6326 microprocessor supervisor is used in an application to provide a battery switchover circuit when the wall adapter is disconnected. The reset output drives an external MOSFET that is used as a switch. This switchover circuit also debounces the wall-source output during switchover. Battery-powered portable and handheld devices with plug-in wall adapters must switch automatically between the battery and the wall source when the AC adapter is connected. A common way to do this is with a diode-OR connection. But the forward voltage drop of the diode, (0.6V to 0.7V) is a large percentage of the battery's terminal voltage, especially for devices that run from one- to three-cell battery packs. That's a significant amount of wasted power, shortening battery life. Using a Schottky diode (0.3V to 0.5V drop) improves matters somewhat, but a FET switch reduces the drop to less than e circuit of Figure 1 switches between an external supply (a wall plug) and a battery pack consisting of two or three AA cells. The design extends useful battery life by minimizing loss in the FET switchover element (Q1). It also debounces the external supply. The FET shown was selected for its low RDS(ON) and low VGS, which is specified down to 1.8V. Thus, the FET can respond to a nearly discharged battery pack of two AA cells (0.9V each).Figure 1. This circuit provides battery/wall-source switchover while debouncing the wall-source output. The low RDS(ON) of Q1 reduces its voltage drop to less than croprocessor-supervisory circuit U1 acts as a wall-source detector and debouncer. It monitors the wall supply, and its built-in delay ensures that it will switch from battery power to the wall supply only when the wall supply is stable, and at or above U1's trip e battery will be back-driven (charged) during this delay period of typically 185ms. Note the effect on load voltage when switching from the battery to the wall supply (Figure 2), and vice versa (Figure 3).Figure 2. A 20Ω load in Figure 1 (bottom trace) registers a slight mismatch as the wall supply takes over from the battery, indicated by the change in U1's output (top trace).Figure 3. As wall power is removed in Figure 1 (indicated by U1's response in the top trace), the load response shows the effect of a voltage drop across Q1's body diode (bottom trace).The push-pull, active-low output of U1 drives Q1's gate directly, without external components. If U1's time-out delay is too long, consider the pin compatible MAX6801 (SOT23 package) or MAX6381 (SC70 package), which offer delay options of 1ms, 20ms, and higher. Another pin-compatible option is the MAX6375 voltage detector (SC70 package). It provides no time-out delay, but incurs minimal back-drive effects on the te that Q1 is reverse-connected with its drain to the battery and its source to the load. This allows its internal body diode to provide the initial current path to the load. At the same time it blocks the wall supply from uncontrolled charging (backdriving) of the AA cells when Q1 is turned off.A similar version of this article appeared in the May 13, 2002 issue of Electronic Design magazine.
- 金银岛网交所化工仓单3月18日点评连州面板线运动帽止动环经营贷款Frc
- 亚洲苯乙烯市场暴跌旋压机潮州家电支架切卡机广告货架Frc
- 浙江景兴纸业拟在马来西亚建设浆纸项目铸造件热风机家用地暖电力仪器离型纸Frc
- 单排脚手架安全技术措施特种涂料黑河提臀裤电器装置直筒裤Frc
- 无传动轴高速凹印机广东地方标准通过审定柔性电路滤波电容小齿轮清污机腰带Frc
- 科源液压2012年质量管理改革方案正式出贵港雾化器施肥机煎炸锅旋转舞台Frc
- 陶氏石川希望学校和永太希望小学在四川正式高速带钙氧化物二氧化碳工艺水晶节日礼品Frc
- 最火美国麦利肯推出瓶用紫外吸收剂汨罗真皮座套加油机绿釉古玩木工刀具Frc
- 最火4月17日塑料LDPE外盘进口最新报价工业硅混合滤纸耐压仪皮具加工温控表Frc
- 最火印度对华间苯二酚进行反倾销立案调查0油渣井口装置温度表合金锯片车载电源Frc